Stationary Combustion Emissions: A Practical Scope 1 Fuel Guide
A synthetic technician in a hard hat and dark-blue workwear stands beside a large boiler with dark casing. A gauge, yellow pipe, valves, silver insulated pipework and nearby tanks are visible. No legible customer name, unit identifier, fuel quantity, emission figure, certificate or assurance statement is shown. Appearance and pipe colour do not prove fuel composition, control rights or safe equipment operation.
Diagram text description
Stationary combustion emissions arise when fixed equipment burns fuel to produce heat, steam, electricity or useful process energy. They include carbon dioxide, methane and nitrous oxide: CO2, CH4 and N2O. For a corporate inventory, whether the source contributes to Scope 1 depends on the organization's chosen boundary and the relevant ownership or control relationship, not simply on where the equipment stands.
A defensible result joins a specific site and unit ID to the fuel actually burned, the original activity unit, suitable gas-specific factors and the reporting period. Missing stock records, an unidentified fuel or an incompatible factor can break that chain even when the spreadsheet arithmetic looks correct.
This guide follows that chain from the equipment register to a reproducible worked calculation. The equipment and quantities are fictional; the example's emission factors are published EPA values. Purchased energy, mobile fuel, fugitive releases and upstream fuel impacts remain distinct source questions rather than being folded into one boiler number.
Decide whether the source is within Scope 1
First establish the inventory perimeter and the unit's relationship to it. An included boiler burning fuel is a stationary combustion source. A truck burning the same fuel is a mobile source. Fuel escaping from a pipe without being burned is a fugitive release, and CO2 released by a non-combustion chemical reaction is a process emission. Different methods may be needed even when these activities occur at the same site.
Purchased electricity or heat creates another distinction. If a third party burns fuel to supply steam bought by the reporting company, the buyer does not simply label that supplier's combustion as its own Scope 1. Acquired-energy accounting and any relevant contractual arrangements need assessment. Conversely, an included on-site boiler's fuel does not become purchased-energy Scope 2 merely because someone else delivered the fuel.
Use the company's consistent consolidation approach and supporting agreements when evaluating owned, leased or shared equipment. An address, a photograph or payment of an invoice alone cannot establish the whole boundary decision. Record which sources are included, which require another method and which control or allocation questions remain unresolved before aggregating the emissions.
Build a complete equipment and fuel inventory
List fixed fuel-burning equipment by site, unit and fuel stream. Boilers, furnaces, heaters, kilns, ovens, turbines, generators and intermittent backup equipment can all matter. Include the reporting dates, operational status and connections to shared meters or tanks. A plant that ran only during an emergency should not disappear merely because it has no regular monthly bill.
The following fictional register separates the source from the supply record. It is an equipment map, not an emissions result.
| Site | Unit | Fuel stream | Period | Activity evidence |
|---|---|---|---|---|
| East Works | Boiler B17 | Distillate No. 2 | Calendar 2025 | Tank and delivery ledger |
| East Works | Generator G4 | Separate diesel supply | Calendar 2025 | Meter and test-run log |
| North Works | Heater H2 | Natural gas | April–December 2025 | Supply meter and bills |
Table 1, shown one row at a time. Every field is retained.
Row 1
- Site
- East Works
- Unit
- Boiler B17
- Fuel stream
- Distillate No. 2
- Period
- Calendar 2025
- Activity evidence
- Tank and delivery ledger
Row 2
- Site
- East Works
- Unit
- Generator G4
- Fuel stream
- Separate diesel supply
- Period
- Calendar 2025
- Activity evidence
- Meter and test-run log
Row 3
- Site
- North Works
- Unit
- Heater H2
- Fuel stream
- Natural gas
- Period
- April–December 2025
- Activity evidence
- Supply meter and bills
Preserve these relationships when grouping records. If two units share a tank, reconcile the tank balance first and document any allocation; do not give each unit the entire delivery quantity. Check acquisitions, closures, replacements and commissioning dates against the asset register. Distinct fuels need distinct activity and factor records, even if a single supplier invoice covers several deliveries.
Use combusted fuel rather than unadjusted purchases
Fuel purchased during a year is not necessarily fuel burned during that year. For a tank-fed source, start with opening stock, add relevant inflows, then subtract closing stock, transfers out and other non-combustion uses or losses. Reconcile the dates and measurement basis before applying emission factors. A delivery may replenish inventory rather than represent immediate combustion.
The upper box adds 1,000 US gallons of opening stock and 9,000 delivered to make 10,000 available in fictional Boiler B17’s 2025 balance. Two arrows divide this quantity into 8,000 gallons burned on the left and 1,500 closing stock plus 500 transferred on the right. Box areas are not proportional quantities. Only the burned amount feeds this stationary-combustion calculation. The footer states the assumption of no other uses or losses and requires separate assessment of transferred fuel.
Diagram text description
Fictional stock example: East Works' included Boiler B17 uses unblended Distillate Fuel Oil No. 2 during calendar 2025. All quantities below use the same US-gallon basis as the later EPA volume factors. Assume the tank serves B17 except for the documented transfer, and that the records establish no other uses, returns or losses in this illustration.
| Balance component | US gallons | Treatment |
|---|---|---|
| Opening stock, 1 January | 1,000 | Add |
| Deliveries during 2025 | 9,000 | Add |
| Closing stock, 31 December | 1,500 | Subtract |
| Transfer to mobile-fuel supply | 500 | Subtract from B17 |
| Other uses or losses | 0 | Explicit fictional assumption |
| Reconciled B17 fuel burned | 8,000 | Calculation input |
Table 2, shown one row at a time. Every field is retained.
Row 1
- Balance component
- Opening stock, 1 January
- US gallons
- 1,000
- Treatment
- Add
Row 2
- Balance component
- Deliveries during 2025
- US gallons
- 9,000
- Treatment
- Add
Row 3
- Balance component
- Closing stock, 31 December
- US gallons
- 1,500
- Treatment
- Subtract
Row 4
- Balance component
- Transfer to mobile-fuel supply
- US gallons
- 500
- Treatment
- Subtract from B17
Row 5
- Balance component
- Other uses or losses
- US gallons
- 0
- Treatment
- Explicit fictional assumption
Row 6
- Balance component
- Reconciled B17 fuel burned
- US gallons
- 8,000
- Treatment
- Calculation input
The balance is 1,000 + 9,000 − 1,500 − 500 = 8,000 US gallons. Applying a factor to the 9,000 gallons of purchases instead would answer a different question. The 500-gallon internal transfer is not erased from the organization's inventory: assess its mobile combustion separately. Likewise, a real spill or methane leak needs the appropriate treatment, not a combustion factor applied as if the fuel burned.
The next step preserves the original volume and uses factors per gallon. CO2 is produced in kilograms, while the selected CH4 and N2O factors produce grams; convert those grams to kilograms before applying each gas's applicable GWP once. The energy-based alternative would require a matching higher-heating-value, or HHV, basis, not an unadjusted lower-heating-value input. The detailed factors and arithmetic follow in the worked example.
This stock balance is a fictional fossil-fuel case, not evidence that any real mixed fuel contains no biomass. Under the corporate method described in EPA's December 2023 guidance, biogenic combustion CO2 is separately reported, while combustion CH4 and N2O remain in the inventory calculation. If B17's fuel composition or a stock measurement were unverified, the fuel and emissions results would remain provisional; a blank record must not silently become the zero used here.
Match activity units to the emission factor
Read both sides of the factor's unit before multiplying. A value per gallon needs gallons, a value per tonne needs mass, and a value per unit of energy needs fuel energy on the specified basis. A litre, a US gallon and an imperial gallon are not interchangeable labels for the same quantity. Keep the original measurement and the documented conversion rather than relabelling a column.
Moving between mass and volume requires an appropriate fuel density and its relevant conditions. Moving from fuel quantity to energy requires heat content. Gas volume also needs compatible reference conditions. These are physical properties, not universal constants that can be inferred from the amount paid to a supplier.
EPA's factor table identifies higher heating values, also called gross calorific values. Lower heating values, or net calorific values, use a different energy basis. Do not multiply an LHV energy quantity by an HHV factor without the appropriate conversion. The volume-based example below uses one published factor route consistently; it does not add another heat-content multiplier after the per-gallon factor. For a real result, select the fuel, grade, technology, reporting basis and factor edition that actually apply.
Calculate CO2 CH4 and N2O separately
Calculate the gases separately before combining their climate-weighted quantities. In symbolic form, mass of gas equals fuel burned multiplied by that gas's compatible emission factor. If the factor is energy-based, the fuel quantity first needs the appropriate heat-content conversion. A carbon-content method for CO2 does not automatically supply the CH4 and N2O results.
Symbolic dimensional calculation for individual gases, not a numerical emissions estimate. Fuel units cancel the denominator of the selected gas-mass emission factor. Convert grams to kilograms where necessary. Multiplying kg of that gas by its selected GWP produces kg CO2e. Add these compatible results for the gases included. Do not reuse this weighting step for a factor already expressed in CO2e, or add its component gases again.
Diagram text description
Next convert each gas mass to CO2e using the selected reporting basis: CO2e from a gas equals its mass multiplied by its GWP. A GWP is a relative weighting over a specified time horizon, not another fuel-consumption factor. Record the assessment basis and horizon rather than mixing values from different tables because they produce a preferred answer.
The numerical example uses EPA's published 100-year values of 28 for CH4 and 265 for N2O from its January 2025 factor table. These are its AR5 values, not a claim that every programme requires that basis. If a selected factor already states kgCO2e per unit of fuel, do not multiply its combined result by GWP again. Also do not combine a total CO2e factor with its component gases a second time.
Handle biomass and mixed fuels explicitly
Biomass combustion still releases gases. Under the corporate inventory treatment described in EPA's stationary-combustion guidance, fossil combustion CO2 contributes to the inventory, whereas biogenic combustion CO2 is tracked and reported separately. Combustion CH4 and N2O from biomass remain part of the inventory's CO2e calculation. Separate reporting is not a finding of zero physical emissions or automatic carbon neutrality.
The diagram separates the gases rather than subtracting all biomass combustion from the inventory. Biogenic CO2 is reported outside the scopes under the stated GHG Protocol treatment. CH4 and N2O are included and converted to CO2e with the selected GWP basis. Mixed fossil and biogenic fuels require the fractions and corresponding emissions to be assessed separately.
Diagram text description
The diagram distinguishes the reporting paths, not the sustainability of a fuel supply. For a mixture, identify the relevant fossil and biogenic components using a supported method and composition evidence. Apply suitable factors to each relevant stream and retain how the split was determined. A marketing label such as renewable, waste-derived or blended is not a substitute for that evidence.
Do not infer the fossil carbon fraction solely from a blend's volume percentage or treat every part of municipal waste as biomass. Fuel properties and the chosen method matter. This guide does not determine a feedstock's land-use impacts, supply-chain footprint or eligibility under a particular regulation. Those questions remain distinct from the combustion reporting split shown here.
Choose a fuel-based or monitored method
Fuel-based estimation uses the quantity combusted and appropriate fuel properties or default factors. Continuous emissions monitoring systems, or CEMS, use measured stack information to determine emissions over time. Neither method is automatically accurate merely because its input comes from an instrument or an official-looking worksheet.
For measurement, check the actual monitored gas, equipment coverage and reporting period, then deal explicitly with unmeasured gases. For fuel-based estimation, check fuel units, factor boundary and gas-specific treatment. Do not count the same CO2 twice by adding a monitoring result to a duplicate fuel-factor estimate. Neither route is complete merely because a number is available.
Diagram text description
| Method | Essential inputs | Quality questions |
|---|---|---|
| Fuel-based | Reconciled fuel, carbon or heat content, suitable factors | Units, fuel specification, measurement gaps and factor fit |
| Monitored CO2 | Concentration, stack flow, time and operating coverage | Calibration, outages, missing data and included exhaust streams |
Table 3, shown one row at a time. Every field is retained.
Row 1
- Method
- Fuel-based
- Essential inputs
- Reconciled fuel, carbon or heat content, suitable factors
- Quality questions
- Units, fuel specification, measurement gaps and factor fit
Row 2
- Method
- Monitored CO2
- Essential inputs
- Concentration, stack flow, time and operating coverage
- Quality questions
- Calibration, outages, missing data and included exhaust streams
EPA's guidance describes CEMS approaches for CO2 and fuel-analysis approaches for CH4 and N2O. A CO2 monitoring result should not be presented as proof that the non-CO2 gases were also measured. Additional burners or exhaust streams outside a monitor's coverage need their own assessment.
Choose the method allowed and supported by the actual reporting programme, equipment and records. Facility-specific carbon or heat-content information can improve a fuel calculation compared with generic volume defaults. Where statutory monitoring or reporting rules apply, check their current requirements separately; this comparison does not determine a particular facility's legal obligations or certify its monitoring system.
Walk through a factor-compatible example
Fictional worked example: carry East Works Boiler B17's calendar-2025 balance through the calculation. Its opening 1,000 gallons plus 9,000 delivered, less 1,500 closing stock and a 500-gallon transfer, gives 8,000 US gallons actually burned. The equipment, activity and absence of other losses are invented; the factor values below are not.
Use Table 1, Stationary Combustion, in EPA's GHG Emission Factors Hub, last modified 15 January 2025. The selected row is Distillate Fuel Oil No. 2. For this teaching case, assume the unblended fuel specification and volume basis match that row. A real calculation must establish that fit rather than treating the example as a universal factor recommendation.
| Gas | Published volume factor | Fuel input | Calculated gas mass |
|---|---|---|---|
| CO2 | 10.21 kg CO2/gallon | 8,000 gallons | 81,680 kg CO2 |
| CH4 | 0.41 g CH4/gallon | 8,000 gallons | 3,280 g CH4 = 3.28 kg CH4 |
| N2O | 0.08 g N2O/gallon | 8,000 gallons | 640 g N2O = 0.64 kg N2O |
Table 4, shown one row at a time. Every field is retained.
Row 1
- Gas
- CO2
- Published volume factor
- 10.21 kg CO2/gallon
- Fuel input
- 8,000 gallons
- Calculated gas mass
- 81,680 kg CO2
Row 2
- Gas
- CH4
- Published volume factor
- 0.41 g CH4/gallon
- Fuel input
- 8,000 gallons
- Calculated gas mass
- 3,280 g CH4 = 3.28 kg CH4
Row 3
- Gas
- N2O
- Published volume factor
- 0.08 g N2O/gallon
- Fuel input
- 8,000 gallons
- Calculated gas mass
- 640 g N2O = 0.64 kg N2O
This is the symbolic sequence made concrete: Q × EF for each gas, followed by gas-specific mass × GWP. The table's CO2 factor produces kilograms, but the other two produce grams. Converting 3,280 grams to 3.28 kilograms and 640 grams to 0.64 kilograms prevents a thousand-fold error when the results are combined. CO2 has a relative weighting of one on this basis.
| Component | Kilograms of gas | 100-year GWP used | Contribution (kgCO2e) |
|---|---|---|---|
| Fossil CO2 | 81,680 | 1 | 81,680 |
| CH4 | 3.28 | 28 | 91.84 |
| N2O | 0.64 | 265 | 169.60 |
| Combined combustion result | Gas masses remain distinct | No additional GWP | 81,941.44 |
Table 5, shown one row at a time. Every field is retained.
Row 1
- Component
- Fossil CO2
- Kilograms of gas
- 81,680
- 100-year GWP used
- 1
- Contribution (kgCO2e)
- 81,680
Row 2
- Component
- CH4
- Kilograms of gas
- 3.28
- 100-year GWP used
- 28
- Contribution (kgCO2e)
- 91.84
Row 3
- Component
- N2O
- Kilograms of gas
- 0.64
- 100-year GWP used
- 265
- Contribution (kgCO2e)
- 169.60
Row 4
- Component
- Combined combustion result
- Kilograms of gas
- Gas masses remain distinct
- 100-year GWP used
- No additional GWP
- Contribution (kgCO2e)
- 81,941.44
Therefore 81,680 + 91.84 + 169.60 = 81,941.44 kgCO2e. Divide by 1,000 to obtain 81.94144 tCO2e, presented as approximately 81.94 tCO2e. Keep the intermediate arithmetic for reproducibility, but do not interpret those decimal places as measured accuracy. This is the direct combustion estimate for B17, not the facility's entire inventory, an independently verified result or a product footprint.
The published table also gives HHV-based energy factors and a default heat content of 0.138 mmBtu per gallon for this fuel. We used its rounded per-gallon factors directly, so no extra HHV multiplication is applied. Multiplying 8,000 gallons by 0.138 would instead produce 1,104 mmBtu for an energy-based route; it is not a second emissions contribution. Separately rounded columns can produce small differences, so identify the chosen route rather than splicing them together or counting both.
The selected GWP values come from the same publication's AR5 100-year table. Neither the factor edition nor the GWP basis is a measurement date for the fictional boiler. Different fuels, equipment circumstances or programme requirements may require another supported approach. No factor was fabricated to complete this example, and no real fuel analysis or supplier record was reviewed.
Because the fictional fuel is assumed entirely fossil, its CO2 follows the fossil inventory path. For an actual biomass mixture, identify and separately report biogenic CO2 under the cited corporate method while retaining the relevant combustion CH4 and N2O. The example does not establish a biogenic fraction, lifecycle neutrality or an avoided-emissions credit. An unresolved fuel identity, unit basis or transfer would prevent presenting its calculated total as settled.
Avoid double counting generated and purchased energy
Keep the fuel and electricity records connected without duplicating the same activity. If an included on-site generator burns fuel and supplies electricity consumed on site, account for its direct combustion under the appropriate Scope 1 method. Do not then apply a purchased-electricity factor to that same self-generated electricity as if it had also been bought from the grid.
Two distinct energy records can exist at one site. The upper lane assumes the generator is included within the chosen organizational boundary and follows its fuel to the direct-combustion result. The lower lane follows a genuinely separate imported electricity record to Scope 2 accounting. It is not a complete rule for shared plants, exports or combined heat and power. Check those arrangements separately, and do not classify all site electricity from one label.
Diagram text description
Separately purchased electricity remains a different input. A site can both generate and import power, so its meter arrangement, imports, exports and internal consumption need to be understood rather than assigning one label to the whole site. Purchased steam or heat likewise follows acquired-energy accounting, not an automatic second combustion entry for the buyer.
Combined heat and power, shared plants and third-party arrangements can require allocation and boundary work beyond this simple contrast. Identify the generating party and the energy stream before combining data. The objective is not to remove legitimate sources from Scope 2, but to avoid counting one energy quantity twice under incompatible descriptions while retaining the actual purchases.
Check completeness and uncertainty before reporting
Review the calculation against the physical operation and its records, not only against the spreadsheet formula. Compare the equipment list with site information, check that all reporting dates are covered and reconcile meter or stock quantities with purchases. Include small or intermittent sources in the assessment rather than assuming they are immaterial without investigation.
| Check | Question that must be answered |
|---|---|
| Equipment | Are all included fixed units and shared supplies identified? |
| Activity | Do dates, opening/closing stock and transfers reconcile? |
| Units | Are volume, mass, reference conditions and heat basis compatible? |
| Factors | Do fuel, technology, edition and gas units match? |
| Composition | Are fossil/biogenic fractions supported where needed? |
| Exceptions | Are estimates, gaps and unresolved decisions visible? |
Table 6, shown one row at a time. Every field is retained.
Row 1
- Check
- Equipment
- Question that must be answered
- Are all included fixed units and shared supplies identified?
Row 2
- Check
- Activity
- Question that must be answered
- Do dates, opening/closing stock and transfers reconcile?
Row 3
- Check
- Units
- Question that must be answered
- Are volume, mass, reference conditions and heat basis compatible?
Row 4
- Check
- Factors
- Question that must be answered
- Do fuel, technology, edition and gas units match?
Row 5
- Check
- Composition
- Question that must be answered
- Are fossil/biogenic fractions supported where needed?
Row 6
- Check
- Exceptions
- Question that must be answered
- Are estimates, gaps and unresolved decisions visible?
Investigate an unexpected year-on-year change: it may reflect actual operation, a stock movement, a new unit, a method change or a data error. Document the explanation instead of quietly adjusting a factor to make the trend look normal. If a missing delivery or uncalibrated meter materially affects the result, explain the limitation and the next evidence needed. A supportable estimate can be useful, but its basis and uncertainty should remain identifiable rather than masquerading as a measured value.
Keep source evidence usable across teams
Give each part of the evidence chain a responsible owner. Site teams may maintain unit identifiers, operating logs and meter records; procurement or finance may hold delivery documents; the inventory team selects and documents the factor and GWP basis. Clear handoffs reduce the risk that two teams both count a delivery or each assume the other resolved a gap.
For B17, keep the opening and closing stock observations, delivery ledger, transfer record, fuel specification, original unit, chosen factor row and edition, calculation and review outcome together through stable references. Preserve versions when a stock reading or fuel classification changes, so the affected emissions result can be traced. Confidential supplier or operational records need not all be reproduced in a public report.
This is neutral information-governance guidance, not a promise that a particular platform provides a proprietary fuel calculator, verifies facility data or guarantees reporting compliance. A well-organized record can expose a missing assumption; it cannot validate that assumption by itself. Assign the unresolved question and evidence request to a named role rather than letting an incomplete field disappear during aggregation.
Put the stationary source in the wider inventory
A stationary-source calculation is one component of a wider inventory. Take its unit ID, reporting period, reconciled fuel, method, gas results and limitations into the appropriate corporate records. Then check how that source fits the organizational boundary and whether its related energy, fugitive or upstream activities require separate treatment.
The worked example shows the sequence: establish the included boiler, reconcile 8,000 gallons actually burned, use one compatible published factor route, convert gas units, apply each GWP once and retain the fossil/biogenic distinction. Its approximate 81.94 tCO2e is an illustrative combustion result, not a complete corporate or lifecycle footprint.
For the next source, repeat the evidence questions rather than copying the number or assuming every boiler burns the same fuel. Broader consolidation, purchased-energy accounting and cross-source reporting need their corresponding guidance. A useful final record makes both the calculation and any unfinished decisions understandable to the next person using it.
Scope 1: direct emissions
