Operational waste treatment branches to Category 5 for third-party treatment and to Scope 1 or 2 for treatment within the company boundary.
Where waste is treated determines which emissions record it belongs in.
Diagram text description

The two routes distinguish the operator of the treatment facility. Third-party treatment of waste generated in operations belongs in Scope 3 Category 5. Treatment in company-owned or controlled facilities follows the applicable Scope 1 and Scope 2 rules.

Calculate a waste disposal carbon footprint from the waste your operations generated, its actual treatment and the emissions attributable to that treatment. For third-party treatment, the result generally belongs in Scope 3 Category 5. A calculation can cover part of a waste register while other loads remain unresolved. State which loads the figure covers so a reader can tell a measured quantity from an estimated result or a missing route.

An inventory records the treatment that occurred. A route comparison asks what would change if the same waste went somewhere else. Calculate the comparison on a common basis and report any avoided emissions separately from the inventory. Changing the reference case changes the comparison, even when the actual waste and its reported treatment stay the same.

The fictional packing and canteen site below has two confirmed treatment routes, one mixed load awaiting a destination record and a separate wastewater question. Its inventory gives a subtotal for supported treatment rows. A separate food-waste comparison tests a different route under the same boundary.

Decide what the waste result covers

Scope 3 Category 5 covers third-party treatment and disposal of waste generated in the reporting company's operations. That includes solid waste and wastewater. Identify the source of the waste and the party that actually treats it. A collector may deliver the load to a transfer station, while a different operator completes the treatment. An invoice showing that waste left the site can establish collection without identifying its destination.

For treatment at a facility owned or controlled by the reporting company, apply its organisational boundary. On-site fuel combustion or process emissions can fall in Scope 1, and purchased energy used to run the treatment can fall in Scope 2. Keep those emissions in their corresponding records. If the company operates a process before a third party takes over, document the boundary between the stages and assign emissions accordingly.

Treatment situationInventory routeEvidence that settles it
Outside facility treats operational wasteScope 3 Category 5Site of origin, operator and final treatment receipt
Company controls the treatmentScope 1 for direct emissions and Scope 2 for purchased energyOrganisational boundary, process records and purchased energy
Customers discard products the company soldScope 3 Category 12Sold-product data and the relevant end-of-life assumptions

Table 1, shown one row at a time. Every field is retained.

Row 1

Treatment situation
Outside facility treats operational waste
Inventory route
Scope 3 Category 5
Evidence that settles it
Site of origin, operator and final treatment receipt

Row 2

Treatment situation
Company controls the treatment
Inventory route
Scope 1 for direct emissions and Scope 2 for purchased energy
Evidence that settles it
Organisational boundary, process records and purchased energy

Row 3

Treatment situation
Customers discard products the company sold
Inventory route
Scope 3 Category 12
Evidence that settles it
Sold-product data and the relevant end-of-life assumptions

Set the optional transport policy before choosing factors. In the example, the inventory counts the third-party treatment attributable to the site and excludes third-party collection transport. If a factor includes transport, request its stage breakdown or choose a factor that matches the stated boundary. Waste produced by suppliers while making purchased goods and discarded products sold to customers have their own value-chain boundaries. Start the operational register with waste from your own sites and period.

Build a filled waste register before choosing factors

This is an explicitly fictional example for Cedar Quay Works, a packing and canteen site, for July 2025. All destinations, documents and quantities are invented. Solid waste weights are net loads after tare. The table records what happened to each stream and who must obtain any missing treatment evidence.

Record and waste streamQuantity and basisTreatment destination and evidenceStatus or next owner
P01. Clean packing paper1,250 kg net, or 1.25 tPaper sorting and preparation at a third-party materials recovery facility. Receiving ticket P01 and collector invoice match.Route confirmed. Use the preparation-only factor for the attributable stage.
F01. Wet canteen food waste600 kg net, or 0.60 tThird-party landfill. Collection note and site receipt F01 match.Route confirmed. Use a food-waste landfill treatment factor for the exercise.
M01. Mixed residual waste350 kg net, or 0.35 tThird-party transfer station intake M01. No final treatment statement.Route open. Facilities lead requests the destination and any onward split from the operator.
W01. Canteen wastewater8 m³ billed dischargeThird-party sewer service. Invoice gives volume without the treatment pathway or organic load.Estimate open. Site environmental lead requests plant and load evidence.

Table 2, shown one row at a time. Every field is retained.

Row 1

Record and waste stream
P01. Clean packing paper
Quantity and basis
1,250 kg net, or 1.25 t
Treatment destination and evidence
Paper sorting and preparation at a third-party materials recovery facility. Receiving ticket P01 and collector invoice match.
Status or next owner
Route confirmed. Use the preparation-only factor for the attributable stage.

Row 2

Record and waste stream
F01. Wet canteen food waste
Quantity and basis
600 kg net, or 0.60 t
Treatment destination and evidence
Third-party landfill. Collection note and site receipt F01 match.
Status or next owner
Route confirmed. Use a food-waste landfill treatment factor for the exercise.

Row 3

Record and waste stream
M01. Mixed residual waste
Quantity and basis
350 kg net, or 0.35 t
Treatment destination and evidence
Third-party transfer station intake M01. No final treatment statement.
Status or next owner
Route open. Facilities lead requests the destination and any onward split from the operator.

Row 4

Record and waste stream
W01. Canteen wastewater
Quantity and basis
8 m³ billed discharge
Treatment destination and evidence
Third-party sewer service. Invoice gives volume without the treatment pathway or organic load.
Status or next owner
Estimate open. Site environmental lead requests plant and load evidence.

The collection invoice repeats the paper quantity shown on the receiving ticket. Both documents support P01. Keep the record once and link both files to it. The mixed load also stays in the register because its measured mass is known. A transfer-station receipt does not tell us whether its contents were sorted, landfilled or sent elsewhere.

Keep the reporting month and site ID on each row when moving the register to another workbook. Include whether quantities are weighed, invoiced or estimated, and keep the factor coverage with each calculation. This is a practical record for the exercise. The important part is that a reviewer can trace the quantity, treatment and outstanding request.

Choose among three methods using the evidence available

Choose the method from the quality of the available treatment evidence. A supplier-specific result uses the waste operator's direct and purchased-energy emissions allocated to the reporting company's waste. Ask what period, waste, facility and stages the allocation covers and how the share was calculated. A whole-facility total needs an attributable share before it can support a site result.

The waste-type-specific method uses a known quantity and a matching factor for the waste type and treatment. Cedar Quay has both activity fields for the paper and food rows. The average-data method uses total waste mass, the shares treated by different methods and compatible average factors. Use supported proportions for the waste population and period being estimated. The method carries greater uncertainty when the mix is derived from broad averages.

Allocated facility emissions support a supplier-specific method. Known waste mass and route support the waste-type method. Supported treatment shares support average data.
Match the calculation method to the evidence available for each waste stream.
Diagram text description

Read each column as an evidence and method pair. A facility allocation can support supplier-specific treatment. Mass with a confirmed waste type and route can support a matching factor. When individual destinations are unknown, a supported treatment mix can support an average estimate.

You can use different methods for different streams if each calculation has a defined boundary and the streams do not overlap. For example, an allocated supplier result may cover the paper preparation while a route factor covers the food landfill. An average estimate can be useful for residual waste if a relevant treatment mix exists. In this example there is no supported mix for M01. Leave that calculation open until the operator supplies evidence or the reviewer approves a separately documented estimate.

Reconcile collection records and treatment quantities

Reconcile collections and receiving records before calculating. Match by site, date, vehicle or load ID, waste stream and net weight. A collector may invoice a monthly total that includes loads with separate weighbridge tickets. Use the confirmed load IDs to decide which documents represent one movement. Keep the evidence links even when the underlying activity is counted once.

For Cedar Quay, the three unique solid loads are 1,250 kg of paper, 600 kg of food and 350 kg of mixed residuals. Together they equal 2,200 kg or 2.20 tonnes. Confirmed routes cover 1.85 tonnes. The remaining 0.35 tonnes have a known mass and an open route. Wastewater is recorded in cubic metres and stays on a separate basis.

The fictional 2.20 tonnes of unique solid waste include 1.25 tonnes of paper and 0.60 tonnes of food with known routes, plus 0.35 tonnes of mixed waste with its route open.
Of the 2.20 tonnes of unique solid waste, 1.85 tonnes have confirmed treatment routes.
Diagram text description

After matching the duplicate paper record, the fictional site has 2.20 tonnes of unique solid waste. The known route group contains 1.25 tonnes of paper and 0.60 tonnes of food. The mixed load accounts for the remaining 0.35 tonnes. Its mass is known while its final destination is open.

Check whether a transfer operator split a load between treatments. Use the destination weights or a documented share and make sure the portions reconcile to the original net mass. For a supported average-data calculation, multiply total tonnes by each treatment share, then by that route's factor, and sum the results. Shares should account for the population they describe. If there is an unexplained difference between recorded mass and treatment quantities, leave it visible and resolve it before reporting full coverage.

Calculate one clearly fictional operational inventory

The following fictional calculation uses illustrative factors for P01 and F01 only. Each factor is expressed in kilograms of carbon dioxide equivalent per tonne of wet or as-received waste, as applicable. The stated boundary excludes collection transport and any avoided material or energy production. The paper factor represents sorting and preparation allocated to this waste generator. The food factor represents its landfill treatment.

Supported rowConversion to tonnesIllustrative treatment factorTreatment emissions
P01 paper preparation1,250 kg ÷ 1,000 kg/t = 1.25 t38 kg CO2e/t1.25 t × 38 kg CO2e/t = 47.50 kg CO2e
F01 food landfill600 kg ÷ 1,000 kg/t = 0.60 t400 kg CO2e/t0.60 t × 400 kg CO2e/t = 240.00 kg CO2e
Supported subtotal1.85 t of the 2.20 t of solid wasteTwo treatment factors on their respective rows287.50 kg CO2e

Table 3, shown one row at a time. Every field is retained.

Row 1

Supported row
P01 paper preparation
Conversion to tonnes
1,250 kg ÷ 1,000 kg/t = 1.25 t
Illustrative treatment factor
38 kg CO2e/t
Treatment emissions
1.25 t × 38 kg CO2e/t = 47.50 kg CO2e

Row 2

Supported row
F01 food landfill
Conversion to tonnes
600 kg ÷ 1,000 kg/t = 0.60 t
Illustrative treatment factor
400 kg CO2e/t
Treatment emissions
0.60 t × 400 kg CO2e/t = 240.00 kg CO2e

Row 3

Supported row
Supported subtotal
Conversion to tonnes
1.85 t of the 2.20 t of solid waste
Illustrative treatment factor
Two treatment factors on their respective rows
Treatment emissions
287.50 kg CO2e

The tonnes in the mass cancel the tonnes in each factor's denominator. The sum, 47.50 plus 240.00, is 287.50 kg CO2e, equivalent to 0.28750 tonnes of CO2e. The digits show the arithmetic. They do not express measured emissions precision. A real report would select a rounding convention suited to the inputs and retain its calculation evidence.

The subtotal covers about 84% of the reconciled solid waste by mass. It says nothing about what percentage of emissions has been covered. The missing 0.35 tonnes could have a different emissions intensity and W01 has no supported treatment estimate. Keep both entries open. In a real inventory, record the factor publisher, version, geography, waste definition, treatment and stages included before accepting either calculated row.

Check whether waste transport is already included

The Category 5 guidance permits optional third-party waste transport. Decide whether the inventory includes it and disclose that choice. A factor may cover treatment only or include a collection leg. If you add a separate transport estimate, verify the source and destination and include only the activity outside the treatment factor's coverage.

Cedar Quay's fictional factors exclude collection, and its July subtotal excludes collection too. If the reporting policy changes, the collector would need to provide enough detail to estimate the attributable movements. A shared route may require a documented allocation. Match the distance, load and factor denominator, and check that a transfer and a final treatment receipt do not both imply the same leg. The optional scope decision does not resolve a missing final destination. It changes which emissions the estimate covers.

Compare treatment routes without netting avoided emissions

Compare the same waste quantity and composition at the same boundary. In this separate fictional scenario, send the 0.60 tonnes of wet canteen food from F01 to industrial composting instead of its actual landfill route. The reference is the July landfill route. Hold the waste composition and wet mass fixed at facility reception. Both estimates cover treatment only and omit collection and displaced products or energy.

Comparison basisLandfill referenceIndustrial compost alternative
Matched input0.60 t of the same wet food waste0.60 t of the same wet food waste
Illustrative treatment factor400 kg CO2e/t150 kg CO2e/t
Treatment emissions0.60 × 400 = 240 kg CO2e0.60 × 150 = 90 kg CO2e
Material uncertaintySite methane generation and gas captureAeration, process controls and reject treatment

Table 4, shown one row at a time. Every field is retained.

Row 1

Comparison basis
Matched input
Landfill reference
0.60 t of the same wet food waste
Industrial compost alternative
0.60 t of the same wet food waste

Row 2

Comparison basis
Illustrative treatment factor
Landfill reference
400 kg CO2e/t
Industrial compost alternative
150 kg CO2e/t

Row 3

Comparison basis
Treatment emissions
Landfill reference
0.60 × 400 = 240 kg CO2e
Industrial compost alternative
0.60 × 150 = 90 kg CO2e

Row 4

Comparison basis
Material uncertainty
Landfill reference
Site methane generation and gas capture
Industrial compost alternative
Aeration, process controls and reject treatment

With transport excluded, fictional treatment of 0.60 tonnes of food gives 240 kg CO2e for the landfill reference and 90 kg CO2e for the compost alternative.
Compare treatment outcomes for the same 0.60 tonnes of fictional food waste.
Diagram text description

Start with the same 0.60 tonnes of wet food waste. The fictional landfill reference has 240 kg CO2e of treatment emissions. The compost alternative has 90 kg CO2e on the same treatment boundary. Their 150 kg CO2e difference describes the scenario only.

Under those assumptions the alternative is 150 kg CO2e lower for this treatment comparison. The difference remains separate from the 287.50 kg CO2e July subtotal, which includes the actual landfill treatment of F01. Changing the landfill's gas capture, the composting process or reject handling could change the comparison. If either route rejects some of the food, include the resulting treatment within a common boundary or disclose why the comparison is incomplete.

A broader decision might include collection, displaced fertiliser or exported energy. Make each added stage and reference product explicit and gather comparable evidence for both routes. Such a wider scenario can answer a different question from the Category 5 subtotal. It cannot establish that a route is best for every site or waste mix. If the site changes treatment later, use the new actual route for that later period.

Apply recycling and energy-recovery allocation carefully

Apply recycling allocation consistently across waste generators and buyers of recycled material. Purchased recycled inputs belong with purchased goods or capital goods as applicable. Treatment of products sold to customers belongs with end-of-life of sold products, Category 12. The paper row here concerns third-party treatment of operational waste. The exercise includes a preparation stage assigned to the generator and excludes recycling stages already allocated to the recycled material. Check the allocation against the factor notes so the same processing is not counted twice.

For third-party waste-to-energy, the Category 5 guidance allocates combustion emissions to the energy consumer's Scope 2. Applicable preparation remains with the waste generator in Category 5, with transport when included under its policy. A company that controls on-site incineration records its combustion in Scope 1. For third-party incineration without energy recovery, the generator includes the combustion emissions in Category 5.

The physical process can emit greenhouse gases even when the inventory allocates combustion to another record. If you compare waste-to-energy with recycling or landfill, state the physical stages and the treatment of any exported electricity. A zero or small number within a particular inventory boundary cannot settle the wider climate comparison.

Handle wastewater as its own evidence problem

Handle wastewater as its own stream. Discharge volume can describe how much liquid reaches the sewer, but the treatment and organic load affect the estimate. Ask who treats the wastewater, which process is used and whether the utility or plant has data attributable to the site. The plant may treat several sources, making the allocation as important as the site meter.

Depending on the method, evidence may include biochemical oxygen demand, or BOD, and chemical oxygen demand, or COD. These measures describe aspects of the organic load. A laboratory concentration and a volume are different inputs. Record sample timing, representative flow and units before combining them. A suitable treatment method may also need information about methane or nitrous oxide and how the plant manages its process.

In the fictional example, W01 has a billed discharge of 8 m³. Treatment and the relevant load evidence remain open. Ask the operator which data are available and whether the factor basis covers this discharge. Keep the volume and the named evidence request in the wastewater register. This gives the reviewer a usable starting point and keeps the wastewater volume separate from the solid waste mass.

Close the example with an action and review register

Close the waste register with an owner and a decision for each gap. For Cedar Quay, the known-route subtotal remains provisional while two treatment questions are open. Preserve the July scope, activity records and factor boundary when asking for additional evidence.

  • Facilities lead. Match M01 to the final destination and any split treatment weights. Update its factor only after the route or a supported estimate is confirmed.
  • Site environmental lead. Resolve the W01 treatment and load basis with the utility or plant. Record the selected wastewater method separately.
  • Inventory reviewer. Check the deduplicated mass, transport policy, allocation and factor versions. Keep the compost scenario beside the inventory with its own assumptions.

Then update the scope statement and the result together. The reader should be able to see the actual treatment covered, any unresolved rows and the separately calculated consequence of switching routes.